The PSRDADA format is used internally within the MWAX correlator and beamformer components. It is not user-facing.
| Table of Contents |
|---|
Pre Correlator
| Keyword | Valid values or Example | Used By | Description |
|---|---|---|---|
| HDR_SIZE | 4096 | PSRDADA | Required by PSRDADA - size of header in bytes (should always be 4096) |
| POPULATED | 0 | 1 | mwax_db2correlate2db | Used to ensure the correlator does not read an incomplete file. 0 means the file is not yet complete, 1 means the file is ready for consumption |
| OBS_ID | 1244973688 | mwax-db2fits | Obs_id of this observation |
| SUBOBS_ID | 1244973688 | mwax-db2fits | GPS second of this part of the observation. Increments in 8 sec intervals |
| COMMAND | CAPTURE | IDLE | QUIT | mwax_db2correlate2db mwax-db2fits | CAPTURE - correlate and produce FITS output for this subobservation IDLE - consume but ignore this subobservation. If there is an existing obs_id in progress, finish the FITS file even if it is not complete QUIT - stop processing and quit immediately |
| UTC_START | 2018-10-11-05:26:14 | PSRDADA mwax-db2fits | Required by PSRDADA. This is the UTC start date/time of the subobservation(?). Used by mwax-db2fits to append a human readable date/time to the filename produced. |
| OBS_OFFSET | 0 (n seconds since start of observation) | PSRDADA mwax-db2fits | Required by PSRDADA. I believe this is the number of seconds offset from the start of the observation. First subobservation will have this set to 0. Second subobservation will be 8, etc. |
NBIT | 8 | mwax_db2correlate2db | Bits per sample (should always be 8) |
| NPOL | 2 | mwax_db2correlate2db mwax-db2fits | Polarisations per tile (i.e. rf_chains) (should always be 2) |
| NTIMESAMPLES | 51200 | mwax_db2correlate2db | Number of timesamples in each input sub-block of a subobservation (nominally sub-blocks are 40 ms) |
| NINPUTS | 256 | n rfinputs | mwax_db2correlate2db | Number of signal paths present in the input subobservation file, to be correlated (must be <= NINPUTS_XGPU) |
| NINPUTS_XGPU | 256 | n rfinputs in multiples of 16 | mwax_db2correlate2db | Number of signal paths actually correlated by xGPU (must be a multiple of 16; must match the number of paths that xGPU has been configured for) |
APPLY_PATH_WEIGHTS | 0 | 1 | mwax_db2correlate2db | Should scalar path weights be applied prior to correlation (for gain normalisation and/or sub-arraying) |
| APPLY_PATH_DELAYS | 0 | 1 | mwax_db2correlate2db | Should fractional path delays be applied prior to correlation (for phasing up to a correlation pointing centre) |
| INT_TIME_MSEC | 200 - 8000 | mwax_db2correlate2db mwax-db2fits | Correlator integration time (milliseconds) |
| FSCRUNCH_FACTOR | 40 (1 - 5120) | mwax_db2correlate2db mwax-db2fits | Correlator frequency scrunch factor: number of ultrafine 250 Hz fine channels to average together |
| APPLY_VIS_WEIGHTS | 0 | 1 | mwax_db2correlate2db | Should data occupancy weights be applied to normalise the output visibilities |
TRANSFER_SIZE | 5269094400 | PSRDADA mwax_db2correlate2db | Total number of bytes of input data for one subobservation (of nominally 8 seconds) |
PROJ_ID | G0008 | mwax-db2fits | Project ID of observation |
| EXPOSURE_SECS | 8 (in incremements of 8 seconds) | mwax-db2fits | Duration of observation in seconds |
| COARSE_CHANNEL | 76 (0 - max receiver channel number == 255) | mwax-db2fits | Receiver channel number |
| CORR_COARSE_CHANNEL | 9 | (1 - coarse channel max) | mwax-db2fits | Correlator channel number - which correlator channel "index" is this? e.g. first channel would be 1. In a 24 channel system, last channel would be 24. This would map to gpubox01-24 in the legacy Correlator |
| SECS_PER_SUBOBS | 8 | mwax_db2correlate2db mwax-db2fits | Number of seconds per subobservation |
UNIXTIME | 1539235574 | mwax-db2fits | Unix time of the start of this observation. This field is used by mwax-db2fits to provide a UNIX timestep for each integration throughout the observation. |
| UNIXTIME_MSEC | 0 | mwax-db2fits | Unix time milliseconds offset of the start of this observation. This will always be 0 with the current setup, but is here for completeness. |
FINE_CHAN_WIDTH_HZ | 10000 | mwax-db2fits | Correlator output fine channel width in Hz |
| NFINE_CHAN | 128 | mwax_db2correlate2db mwax-db2fits | Correlator output number of fine channels |
| BANDWIDTH_HZ | 1280000 | mwax-db2fits | Coarse channel passband width in Hz, i.e. the channel spacing |
SAMPLE_RATE | 1280000 | mwax_db2correlate2db | Sample rate of input data in samples/s (whether critically-sampled or oversampled) |
| MC_IP | 0.0.0.0 | mwax-db2fits | Multicast IP for this coarse channel (for debug purposes) |
| MC_PORT | 0 | mwax-db2fits | Multicast port for this coarse channel (for debug purposes) |
| MC_SRC_IP | 0.0.0.0 | Not used (yet) | Multicast source IP of data for this coarse channel (for debug purposes) |
...